The easiest way to remove fence posts depends on the type of fence post that you have. Wooden posts can often be removed relatively easily by using a shovel or crowbar to help pry the post out of the ground.
If the post has been cemented in, then you may need to use a jackhammer or other power tool to break it up and remove it. Chain link posts, on the other hand, can often be deconstructed from the ground up by manually removing pieces of the fence and taking the post apart into smaller parts until it is removed.
With metal posts, you may need to cut the post off with a saw, as well as using a jackhammer to remove any underground portions. If you are unsure of how to remove a fence post, you may want to reach out to a professional to have them help safely and efficiently remove it.
Table of Contents
How do you get a post out of the ground easily?
Removing a post from the ground can be challenging, but there are a few steps you can take to make the process easier.
First, if the post is held in place primarily by dirt and soil,you should dig around the post so that you can access its base. Make sure the hole is at least twice as wide as the post itself, and that you proceed carefully.
You can then use leverage to pull the post out – either by hand or with a tool like a come-along.
If the post is particularly deep, you may need to use a post hole digger or a claw bar to remove the soil or, for deeper posts, a backhoe to free it from the ground.
Finally, if the post is firmly set in concrete, you may need to use a rotary hammer and a set of drill bits to remove it. At a minimum, a sledgehammer and chisel are also effective tools. If you should go this route, make sure to wear protective eye wear and gloves.
How do you remove cemented posts?
Removing cemented posts can be a difficult job and should be done with caution. The best way to go about it is to first start by digging around the post. You will need to dig down about six to eight inches in the soil to get to the concrete.
Once you have exposed the concrete, use a sledgehammer or crowbar to break it up into smaller pieces. Once the cemented post is loosened, you can try to pull it out of the ground by hand. It is also possible to use a wire cutter to help pull it out, although it might take time.
If the post is too stubborn and won’t come out, you may need to use an electric jackhammer or a jack to jack the post out. Make sure to wear safety equipment such as goggles and gloves when using any type of power tool.
Once the post is out, clean up the area and dispose of the concrete pieces.
How much should I charge to remove a chain link fence?
The cost to remove a chain link fence will depend on a variety of factors, including the size of the fence, the type of material used, and the complexity of the project. If the fence is relatively small and the material is not particularly expensive, it may cost as little as a few hundred dollars.
If the project is larger and made of a more expensive material, the cost could increase to a few thousand dollars. The complexity of the project will also be a factor. If the fence is anchored in concrete, for example, the cost may be higher due to the additional labor required to remove the concrete.
Additionally, the removal of any hazardous material added to the area due to the installation of the fence can have an impact on the cost. Ultimately, the best way to determine an accurate estimate of the removal cost is to contact a qualified professional who can evaluate the chain link fence in question and provide an accurate estimate.
How much does labor cost to install a chain link fence?
The cost of labor to install a chain link fence will depend on a few factors, such as the size and height of the fence you need, fencing material costs and the amount of terrain the fence needs to cover.
Generally speaking, labor costs to install a chain link fence start at around $7. 50 per linear foot and can go up to $15 or $20 per linear foot. Labor costs typically include the installation of posts, fabricating and tightening the chain link panels, and attaching gates.
Additional costs may include the removal of any existing fences (if applicable) and the materials needed to build the new fence, such as posts, fabric, and accessories like latches, hinges and wheel assemblies for gates, as well as any labor needed to unload and transport the supplies to the job site.
Depending on the labor costs in your area, you can expect to pay anywhere from around $1,000 for a low-end 50-100-foot fence with basic gate options (4-foot to 6-foot in height), to up to $10,000 for a 250-300-foot fence with upscale gates (up to 8-foot in height).
Does chain link fence decrease property value?
The answer to this question depends on many factors, such as the location, design, and aesthetic value of the chain link fence. In general, a chain link fence may provide a cost-effective means of increasing security to a property and offering additional fencing options, but it may not necessarily increase the property value.
In some cases, a chain link fence may blend in with surrounding fencing styles and increase the overall appeal of a property. In other cases, a chain link fence might be viewed as an eyesore. Additionally, chain link fences are not always the best choice when it comes to long-term durability and longevity.
This can be especially true in areas where the fence is exposed to high winds and saltwater.
Ultimately, the value of a house that has a chain link fence can vary greatly depending on the quality of the fence and its overall aesthetic value. While it is possible for a chain link fence to improve the overall appeal of a property, it is not necessarily a guarantee that it will increase its value.
Can you DIY concrete removal?
Yes, it is possible for you to do your own concrete removal, however, depending on the amount of concrete being removed and the size of the project, it can be an extremely labor intensive and time-consuming task.
Depending on the amount of concrete being removed, it may be more cost and time-effective to hire a professional concrete removal company.
DIY concrete removal generally consists of the following steps: first, you need to demolish the concrete by breaking it into smaller pieces with a sledgehammer and a cold chisel. After the concrete is broken apart, you must dig out the pieces and separate the chunks from the dirt and rubble.
Then it is important to rent the appropriate equipment to haul off the concrete. A wheelbarrow, dolly, and a truck or trailer may be necessary to complete the job. Once the concrete is removed you will need to even out the area and spread new soil, grade it, and eventually lay down fresh landscape fabric and new gravel.
While performing your own concrete removal can be a cost-effective option, it is important to consider the time and effort you may be putting in for the job. If you aren’t prepared to do the work, hiring a professional concrete removal company may be the way to go, or at the very least, seek advice from a professional before you begin the project.
