The exact number of VERSA-LOK blocks per pallet will vary depending on the size and shape of the blocks, as well as on the size of the pallet. Generally speaking, however, a pallet of VERSA-LOK blocks is typically sized to contain 168 cubic feet or 3300 pounds of block.
For the commonly available 4x8x16 inch blocks, this typically translates to anywhere from 350-460 blocks per pallet. Some more unusual sizes may have fewer blocks per pallet, while oddly shaped blocks may have more.
Table of Contents
How much does a VERSA-LOK weigh?
The weight of VERSA-LOK units varies depending on the size, shape and type of the unit. Standard retaining wall units are generally the lightest and weigh approximately 12-16 pounds. Corner units can weigh between 18-25 pounds.
Caps generally range from 12-25 pounds and the larger ones can reach up to 30-45 pounds. Wing wall units can typically weigh between 22-30 pounds. VERSA-LOK’s Geo Grid technology provides a stable, load-bearing wall with as little as 40% of the weight of a traditional block wall.
VERSA-LOK also carries a wide variety of accessories such as decorative panels, wall caps, vent blocks, columns, wrought iron railings and fence panels that can range from 14 pounds to 350 pounds each.
How heavy are VERSA-LOK blocks?
VERSA-LOK blocks vary in weight depending on their type and size. Standard, Square Foot VERSA-LOK blocks weigh between 33 and 35 lbs each, while Corner and Wall-Tie units weigh 16 and 24 lbs. respectively.
The Standard VERSA-LOK blocks are available in 4″ to 10″ blocks, and are 4″ thick, while Corner and Wall-Tie units are 8″ thick. All of the blocks have the same face dimensions and use the same VERSA-LOK pins for installation, but the larger blocks are designed with increased cavity volume for increased strength and support.
How high can you stack VERSA-LOK?
VERSA-LOK Retaining Wall Systems have been designed and engineered to meet the highest standards of strength and integrity. With appropriate sizing, specifications, and installation of mortarless VERSA-LOK units, walls of virtually any height can be constructed.
When building taller retaining walls, VERSA-LOK recommends contacting a VERSA-LOK Authorized Contractor to ensure the wall will meet all codes and regulations. A qualified engineer may also be necessary for walls that exceed 6 feet in height.
When installing taller walls, additional reinforcement and select backfill may be necessary. In addition, use of geogrid should be considered to increase stability in high-seismic areas. With these considerations in mind, VERSA-LOK can easily accommodate walls up to 10 feet tall without the need for additional reinforcements.
What is the size of a VERSA-LOK block?
VERSA-LOK blocks come in a variety of sizes to suit your construction project needs. Standard and cornerblocks are 4″H x 16″W x 12″D, while the standard pillar block is 8″H x 16″W x 12″D. There are also extra-large blocks available at 8″H x 24″W x 12″D.
VERSA-LOK offers a wide range of capped and tumbled block styles and colors, as well as speciality shapes and sizes, to suit any construction project. VERSA-LOK blocks are made from the highest quality concrete and are designed to last for many years.
What colors does VERSA-LOK come in?
VERSA-LOK offers modular retaining wall systems in a wide range of colors, including Riverbed, Charcoal, Tan, Graphite, and Weathered Bronze. Riverbed is the most popular color for VERSA-LOK walls due to its natural appearance and the ability to blend in with plantings and other surroundings.
The other colors are great for creating contrast and achieving an even more customized look. Weathered Bronze is great for homeowners who want to achieve a rustic, aged look for their walls. Tan is a great choice that is versatile and pairs well with numerous colors and styles.
Graphite imparts an elegant and sophisticated look, while Charcoal gives walls a dark and powerful appearance.
How many retaining wall caps do I need?
The number of retaining wall caps that you need largely depends on the size and shape of your wall. Generally, you will need one cap for every 16-24 inches (40-61 cm) of wall. If your wall is curved, you may need a slightly higher ratio of caps to ensure proper coverage.
Consider covering the entire length of your wall, as well as any protruding corners and edges, with a cap to ensure that your wall is fully sealed. When considering the total number of caps, keep in mind the importance of using durable materials that can guard against moisture and other environmental factors that may wear out the wall over time.
Additionally, make sure your caps are suitable for the conditions of your area. Once you have the exact measurements and specifications for your retaining wall and caps, it is a good idea to consult with a professional to make sure that you are choosing the right materials and amounts of caps to create a safe, long-lasting wall.
How do you glue Versa Lok caps?
Versa Lok caps are one of the most popular retaining walls blocks used in landscaping. To attach them properly, you will need a special adhesive specifically made for Versa Lok caps. To glue Versa Lok caps together, first, clean the caps and mortar joints with a scrub brush and warm, soapy water to remove any dirt or debris.
Allow the blocks and mortar joints to completely dry before applying the adhesive. With a caulking gun, apply a bead of adhesive around the top of the completed wall. Take one Versa Lok cap and press it firmly into place.
Apply pressure with your hand to make sure the cap makes contact with the adhesive. Do this with each Versa Lok cap until the wall is complete. Leave it to sit for at least 24 to 48 hours to let the adhesive cure.
Once it is cured, the Versa Lok caps are securely glued to the wall.
How much should a wall cap overhang?
A wall cap should overhang six inches in order to provide a proper drainage system. This will stop moisture from collecting and seeping into the masonry and causing deterioration over time. If quarter round shingles are being used, they should overhang a minimum of one inch.
Additionally, the masonry should have a 4 inch overhang, and any coping stones that are being used should have a 3 inch overhang. This will ensure that water will properly run off the wall and not collect at the top of the wall, which could cause long-term damage.
What is the retaining wall system?
The retaining wall system is an integral part of landscape design to provide stability to slopes and prevent soil erosion. It is a structure that is used to hold back soil and debris while providing support for surrounding infrastructure like roads and buildings.
The most common type of retaining wall system consists of concrete blocks, retaining walls, and geotextiles. Each type of system may be utilized for different circumstances, but all provide the same basic purpose.
The concrete blocks are pre-formed to specific sizes and strengths depending on the size and height of the wall. These blocks are then stacked on top of each other and anchored to the ground. If needed, geotexile material is then applied, which helps to bind the blocks together and prevent sagging.
The blocks are then grouted and sealed to achieve maximum strength and durability.
The retaining walls, also known as gravity walls, are created by excavating the soil behind them and replacing it with engineered fill materials. These walls are then reinforced with steel bars to improve their strength and stability and typically stand between 3 to 8 feet in height.
Gravity walls can be curved to provide extra support for large slopes, but must be reinforced with appropriate ties to ensure proper stability.
Geotextiles are used to provide the additional support needed for steep slopes or cuts. These fabric-like sheets are designed to allow water and particles to pass through them while preventing seepage and water buildup.
Geotextiles are usually placed at the top or bottom of the slope before the retaining wall blocks are installed to help hold soil in place.
The retaining wall system is a powerful and reliable way to provide stability and erosion control along slopes to both residential and commercial properties. It is an important part of any landscape design that provides both structure and strength, while maintaining a level of aesthetics that can be enjoyed by everyone.
What is the main function of retaining wall?
Retaining walls are structures designed to hold soil and other materials on one side, while preventing the soil from eroding or slipping away from the other side. They are typically used in situations where the land is naturally sloped or graded, or where additional grades need to be created for agricultural, landscaping or building purposes.
While the most common application of retaining walls is along residential or commercial property lines, they can also be seen in parks, gardens, and many different kinds of natural areas. Retaining walls are typically built out of various materials, such as stone, concrete, steel, wood, vinyl, and more and can be designed to go around almost any kind of terrain.
The main function of retaining walls is to provide support and stabilization to an area of land, while also helping to prevent land erosion, landslides, mudslides, and other related issues. They are also often used to prevent the land from becoming too steep, preventing it from becoming dangerous or inconvenient for vehicular or pedestrian traffic.
In addition to serving as a critical erosion control measure, retaining walls can also prevent surface water from flooding or inundating areas where it would otherwise be a problem.
