Setting up a 35G hub can be an intimidating task for the uninitiated, but it’s actually quite straightforward. Below are the steps to help you get up and running:
1. Connect the power supply: You should have received a power cable along with the 35G hub. Connect one end of the cable to the power supply while the other end to the hub. Once properly connected, turn on the power supply.
2. Link the 35G hub to a router: Use an Ethernet cable to link the 35G hub to the router. The connection should look something like this ‘router -> 35g hub -> PC/laptop’.
3. Configure the 35G hub’s settings: Depending on the make and model of your 35G hub, the set up process may vary slightly. Ideally, use the manual or the manufacturer’s guide to properly configure the settings.
Once completed, you should be able to connect up to 35 computers or devices to the network through the hub.
4. Connect the required devices: With the settings completed, now connect the required devices to the 35G hub. Connect one end of the Ethernet cable to the required device’s network port and the other end to the port on the hub.
There you have! Congratulations, your 35G hub is now set up.
Table of Contents
How do I setup a 3 wireless router?
Setting up a three-wireless router is a relatively simple process. The process involves connecting all three routers together to create a wireless network. To begin, you will need the following items: three wireless routers, a modem, Ethernet cables, and a power supply.
1. First, plug one of the wireless routers into your modem using an Ethernet cable. Turn on the router and configure the settings to your preference.
2. Next, plug the other two routers into the first router, using one Ethernet cable for each router.
3. Configure the settings on the secondary routers to match the first router’s IP address, subnet mask, and gateway address.
4. Finally, power on the remaining two routers and connect them to the same wireless network as the first router. Make sure the SSID, channel, and Wi-Fi security settings are set to the same on all three routers.
Once the routers are all connected, you should now have a secure, reliable wireless network.
Why wont my three hub connect to the Internet?
There could be several potential issues as to why your three hub isn’t connecting to the internet. The first being that your broadband connection is not activated or there are problems with your ISP.
This can be confirmed by checking the status lights on your router. If all of the lights are on, then it is likely an issue with your three hub.
Another potential cause could be that there is a firewall enabled on the device that is preventing incoming connections from the internet. You should check the settings on the router or three hub and make sure that there is no unneeded security settings enabled.
It is also possible that your local area network settings are misconfigured and needs to be checked.
Finally, if none of the above are the problem, then it is likely that there is a hardware issue with your devices. You can test this by connecting a second device directly to your router using an ethernet cable.
If the second device connects to the internet, then it is likely that the issue is with your three hub.
If you are still having problems connecting to the internet, then the best idea would be to contact your ISP or manufacturer of the three hub to receive additional assistance.
Is the 5G hub from three good?
The 5G Hub from Three is a great option if you are looking for an all-in-one way to access both home and mobile broadband. It can connect up to 64 devices at a time and at speeds of up to 100Mb. It also has a UK approved 5G modem, meaning that you will have access to the latest 5G speeds.
It comes with a generous 50GB data allowance and it is compatible with most major networks, so you can expect reliable coverage wherever you go. Overall it is an ideal solution for anyone looking for an easy way to take advantage of 5G connectivity for their home or out and about.
What 5G hub does three use?
Three is a mobile network provider that is offering a 5G hub called the Three 5G Hub. It is a portable device that can provide superfast 5G speeds when connected to a compatible 5G network. The Three 5G Hub is powered by the Qualcomm Snapdragon X55 5G Modem-RF System, which is an integrated modem-to-antenna solution that provides download speeds of up to 1.
5 Gbps. It can be used with a range of 5G compatible phones via the dual-SIM slot, and also supports a range of accessories such as USB storage, power banks, and routers. The Three 5G Hub also has a touchscreen display, allowing you to keep track of your data usage and manage the device easily.
It is available for purchase from Three stores and online, and from a range of other retailers.
Can you have 3 routers in one house?
Yes, you can have 3 routers in one house. This could be beneficial if you want to expand your Wi-Fi coverage, as each router can cover a certain area and having three routers would give you much more coverage.
Additionally, you can use the three routers to create multiple networks in the house so that each person in the house can have their own separate network. This can be beneficial if there are lots of people in the house who all want to use the internet at the same time, as this would reduce internet speed issues.
To set up three routers in one house, you can first connect the main router to the modem and then connect the two additional routers to the main router. Remember to keep the two additional routers at least 3 m away from the main router to avoid signal interference.
You can also set up the three routers in a mesh network in order to provide better Wi-Fi coverage across your whole house.
Why does my router have 3 Wi-Fi networks?
Your router may have three Wi-Fi networks because you have enabled a feature called “Dual Band Wi-Fi”. Dual Band allows your router to broadcast two separate Wi-Fi networks, with one on the 2. 4 GHz frequency band and the other on the 5 GHz frequency band.
By having two separate Wi-Fi networks, you can take advantage of the benefits of each frequency band. The 2. 4 GHz band provides longer range, but the 5 GHz band offers faster speeds since it is less congested.
By having two networks, you can better utilize and optimize the connection speeds and range of your Wi-Fi device, giving you a better experience.
How do I connect my wireless router to the Internet?
Connecting your wireless router to the Internet is quite straightforward. First, make sure that you have an active internet connection. If it is a wired connection, you will need to connect an Ethernet cable from your modem to the router’s WAN port.
If your internet service is provided through a DSL connection, then you need to connect your modem to the router’s DSL port. Then, connect to the wireless router using your laptop or desktop computer and also power it up.
After that, access the router’s web interface using an IP address. The default IP address is usually printed on the back of your router or in the user manual. This will bring you to the router’s settings.
In the settings, find the section on connecting to the internet and configure your connection settings. You will need to know your ISP’s username, password and DNS server address. Once the configuration is complete, save the settings and you should now be connected.
Why is my three 4G hub not working?
It is difficult to tell without more information as to why your three 4G hub is not working. However, there are several possible causes that could be the source of the issue. One possibility is that you may not have the correct frequency or settings enabled on the 4G hub.
Additionally, the hub may not be in a strong enough coverage area to make reliable connections, or the 4G signal may be too weak.
It is also possible that the issue is software related and could be the result of an outdated operating system, malware, or a buggy software patch. The problem could be with the hardware as well, such as the antenna or the modem.
In order to understand and troubleshoot why the 4G hub is not functioning optimally, it could be beneficial to test the hub in different environments or locations. Make sure to also check that the settings are updated, make sure not to stress the hub’s capacity with too many connections and try restarting the hub multiple times.
If the issue persists, it may be necessary to replace the 4G hub.
Why is my 4G not activated?
There could be a few reasons why your 4G may not be activated. The most likely explanations are that:
1. Your SIM card may not be activated. Make sure that your SIM card is active and is eligible for 4G or check to see if the 4G/LTE option is enabled in your phone.
2. The coverage may not be available in your area. Even if you have a 4G enabled phone, you may not be able to access the 4G network if your area doesn’t have the coverage. Check with your carrier to see if they offer 4G coverage in your area.
3. Your device may not be 4G compatible. Many devices require a specific chip or technology that allows you to use 4G. Check with your manufacturer or carrier to find out if your device is compatible and if there are any updates that you need to install.
4. You may have been switched to a 3G or 2G connection due to a technical issue. If your carrier is experiencing a technical issue, your phone may be automatically switched to a lower connection speed.
You can contact your carrier to find out if there are any known issues.
5. Your phone may be in power saving mode. Some phones have a power saving mode that autmatically switches to a lower connection speed to save battery. Make sure that you are not in power saving mode or that you have enabled the 4G option in your phone settings.
If you have done all of these things and you still can’t access the 4G network, you may need to call your carrier for further assistance.
How do I connect my hub to Wi-Fi?
To connect your hub to Wifi, you will need to follow these steps:
1. Locate the network name and password for your wifi network. This should be on your wifi router or modem, or in the documents that came with it.
2. Connect your hub to power.
3. Using your device, open the hub’s settings page. This can typically be found by entering the hub’s IP address into a web browser.
4. In the settings page, locate the network connection and enter the network name (or SSID) and the password for your wifi.
5. Save your settings.
6. Wait for the hub to connect to your wifi. This can typically take a few minutes.
7. Once your hub has connected to wifi, it should be ready to use. You may need to restart your hub or any devices that are connected to it before they are able to connect to the internet.
Why do I have 4G but nothing loads?
Having 4G but nothing loading can be a very frustrating experience. And it’s important to identify and address them in order to get back up and running.
The first and most common cause of this is due to a service outage in your area or network. You can typically verify if this is the case by searching the web or checking your network provider’s website for the latest updates.
The second cause is that your mobile device is not compatible with the technology used by your network provider. You can typically verify this by contacting your service provider and seeing if they can determine whether or not your device is compatible.
The third cause is that there may be a problem with the antenna on your device. Try moving to a different location and see if your signal improves. If the issue persists, it may be time to visit a service center and have the antenna replaced.
Finally, the issue could be caused by a weak 4G signal in your area. This can be due to many different factors, such as the distance between you and the nearest cell tower or the area being thickly wooded or hilly.
If this is the case, you may need to upgrade to an antenna with a higher power and range or switch to a different service provider that has better coverage in your area.
Identifying the cause of why you have 4G but nothing loading can help you get back on track quickly and without any major frustration.
Why is the blue light flashing on my three 4G Hub?
The blue light flashing on your Three 4G Hub indicates that either an update is in process or an internet connection has been established. The blue light is a standard indicator used on most wireless devices and routers to signal a successful connection or signal that a device is downloading an update.
When the blue light is constantly flashing, it usually means that your 4G Hub is downloading or installing an update or security patch. It could also mean that the signal strength or signal range of your 4G Hub is too weak and needs to be adjusted.
If the blue light is flashing for an extended period of time, you may need to log into the hub, then check for any available updates, adjust the signal strength, or reset the router entirely.
Why has my three got no signal?
There are a few reasons why your device may not have any signal. The most common reasons are as follows:
1. You are in an area with poor coverage. Coverage can vary depending on the location and type of device being used. Make sure you are in an area with good coverage and ensure your device is compatible with your network’s frequency.
2. The SIM card is not inserted properly. Make sure the SIM card is properly inserted and the phone is unlocked before attempting to use it.
3. You are in an area that is seeing a high level of congestion. During peak times, cellular networks can become overwhelmed, causing dropped calls and decreased signal strength.
4. You could have used up all your service minutes or data. If you have used up all of your prepaid minutes or data, you will not have a signal. You may need to purchase additional service or data in order to have access to a signal.
5. The network settings or APN settings on the device may not be set up correctly. Check the settings on the device and make sure the device is configured to connect to the correct network.
If none of these solutions have worked, you may need to contact your cellular provider for further assistance.
